Hammerhead Service-30 Pool Vacuum Cleaning Machine with 30" Head and 60' Cord.
Service-21 and Service-30 units are meant for pool-to-pool route work, and include a mount assembly for transport. Mount assemblies (HH1306) are compatible with any 2" hitch receiver (vehicle hitch not included). The two standard units are the Service-21, which has a 21" vacuum head and a 40ft power cord, and the Service-30, which has a 30" vacuum head and a 60ft power cord. Service-21 units are also available with a 60ft power cord as an option. Service units ship partially assembled. Some assembly and set-up of the vehicle mount is required.
SERVICE UNITS - FOR POOL ROUTE TECHNICIANS
Service-21 and Service-30 units are meant for pool-to-pool route work, and include a mount assembly for transport. Mount assemblies (HH1306) are compatible with any 2" hitch receiver (vehicle hitch not included). The two standard units are the Service-21, which has a 21" vacuum head and a 40ft power cord, and the Service-30, which has a 30" vacuum head and a 60ft power cord. Service-21 units are also available with a 60ft power cord as an option. (See Optional Configurations below). Service units ship partially assembled. Some assembly and set-up of the vehicle mount is required. (Due to ongoing improvements, products may be slightly different than pictured).
NOT INCLUDED:
-
12 VOLT DEEP CYCLE MARINE BATTERY
-
BATTERY CHARGER
-
STANDARD POOL POLE
SPECIFICATIONS:
-
21" OR 30" INJECTION MOLDED VACUUM HEAD
-
NON-MARKING, BEARINGLESS, CAST URETHANE HEAD WHEELS
-
STAINLESS POLE SWIVEL MOUNT (two position adjustable angle standard on the Service-30)
-
ALL STAINLESS HARDWARE
-
FEATURING THE PATENTED SMART SWITCH™ (The new HH1062 Smart Switch comes standard on all Hammer-Head pool cleaning units. SMART SWITCH™ features include a motor-saving overload sensor, two speeds, and an automatic shutoff when the motor is out of the water for more than a minute).
-
L.E.D. battery voltage meter
-
SEALED AND PRESSURE TESTED MOTOR
-
40FT OR 60FT FLOATING POWER CORD
-
TWO BLADE PROPELLER
-
WELDED ALUMINUM CADDY CART
-
20" MAG BMX-STYLE CART WHEELS
-
NON-MARKING SOLID TIRES
-
STAINLESS WHEEL BEARINGS
-
VEHICLE MOUNT ASSEMBLY (HH1306) **Your vehicle must be equipped with a standard 2” hitch receiver.
-
TWO DEBRIS BAGS (HH1506 AND HH1508)
-
SERVICE-21 WEIGHT WITH 27 SERIES MARINE BATTERY: 155 LBS
(approximate) -
SERVICE-30 WEIGHT WITH 27 SERIES MARINE BATTERY: 157 LBS
(approximate) -
21" VACUUM HEAD & MOTOR WEIGHT: 11 LBS
-
30" VACUUM HEAD & MOTOR WEIGHT: 13 LBS
OPTIONAL CONFIGURATIONS:
-
SERVICE-21-60 (with 60ft power cord)
-
SERVICE-21-NM (without the vehicle mount assembly)
-
SERVICE-30-NM (without the vehicle mount assembly)
-
SERV-CART (complete cart assembly only)
-
SERV-CART-NM (complete cart assembly without the vehicle mount)
-
HH1070 CART FRAME ONLY (see PARTS)
SHIPPING DIMENSIONS:
-
PALLETIZED DIMENSIONS: 30 X 34 X 52 HIGH (one unit per pallet)
-
SHIPPING WEIGHT: 110lbs
-
FREIGHT CLASS: 250
COMPLETE VACUUM HEAD ASSEMBLIES
NOT INCLUDED:
-
12 VOLT DEEP CYCLE MARINE BATTERY
-
BATTERY CHARGER
-
STANDARD POOL POLE
-
BATTERY CASE, BATTERY CONNECTORS, CADDY CART, OR ON/OFF SWITCH
-
PLEASE NOTE: Complete vacuum heads do not come with battery-side connections. Wire ends are bare for connection to a Hammer-Head cart or directly to a 12 volt battery using ring terminals or alligator clips. Caution: Direct wire battery connections without the use of a Smart Switch™ or fuse could result in motor damage and may not be covered under warranty.
SPECIFICATIONS:
-
30" INJECTION MOLDED VACUUM HEAD
-
CLEARANCE OVER POOL FLOOR = 1"
-
NON-MARKING, BEARING-LESS, CAST URETHANE HEAD WHEELS
-
STAINLESS POLE SWIVEL MOUNT (two position adjustable angle standard on the HH1320 30" COMPLETE VACUUM HEAD)
-
ALL STAINLESS HARDWARE
-
35# THRUST PRESSURIZED MOTOR
-
40FT OR 60FT FLOATING POWER CORD
-
TWO BLADE PROPELLER
-
ONE DEBRIS BAG (HH1508 SUPERFINE)
-
30" VACUUM HEAD & MOTOR WEIGHT: 13 LBS
-
SHIPPING DIMENSIONS: 31" X 19" X 13"
-
ACTUAL SHIPPING WEIGHT: 26 LBS
